T-REX Grilles Special Edition Laser Billet Series Lower Bumper Grille Insert; Flat Black (10-14 F-150 Raptor)
$231.48
In Stock
Chat with us
Have a question? Ask a Specialist.
+1 (902) 361-8221 Start Live Chat
Description
Luxurious 3D Contoured Style. The T-REX Special Edition Laser Billet Lower Bumper grille Insert just looks stylish. It features precision cut billet that closely follows the Raptors contours for a unique look. Additionally, the aircraft grade aluminum provides the grille with strength and toughness while still being lightweight. Set your Raptor apart with the eye-catching 3D contouring that this grille provides.Made with Aircraft Grade Aluminum. The Billet Lower Bumper grille Insert is made…
10 reviews for T-REX Grilles Special Edition Laser Billet Series Lower Bumper Grille Insert; Flat Black (10-14 F-150 Raptor)
Only logged in customers who have purchased this product may leave a review.
Related products
Recently Viewed Products
CWW –
It fills up and cleans up the front end look. I also like the protection factor. I had it professionally installed as I had a bit of trouble trying to get the screws installed.
formytruck –
got it very fast. easy to install. makes truck look so much better
NormanB. –
It looks good to me. I submitted a photo as well but I have a white f-150 with chrome tires and I think it looks good. The install requires cutting and drilling of your existing grille which is a no turning back experience, but simple to do. Plus the chrome outer square is the same so if yours is scratched or chipped this wont replace it, it only removes the center section and adds the billet insert. Very sturdy, solid and well made. It’s just up to your tastes or the overall look your shooting for on your truck. The install was simple like I said but at my lazy Sunday pace it was maybe 2-4 hours and will require easy and simple cutting/drilling. Instructions were also crystal clear.
Topdad71 –
This was super easy to install! And it make the large hole in the front bumper look perfect! Look like it came factory! Adds Style!!
JamesJ –
Easy to install and looks great on my front end. Like the finish .
BrianB –
Looks great. If you are close up, you can see though into the intake. But from a distance it does show up like that. Look amazing coming down the road.
LM12V6r –
Nice snug fit so there’s no vibration. You need a little patience getting the screws in and tight but when you’re finished it looks like it came from the factory that way! Plenty of unrestricted air flow for the radiators along with great and much needed protection keeping them safe from flying road debris. Great product and I would buy it again in a heartbeat. FYI I only spend time writing a review for an exceptional product and to me this is.
King –
Easy upgrade, 15-20 minutes while you make the clip washers work and your head is upside down in the hood. A mini ratchet with a Phillips screwdriver head is the tool you want to do this quickly. Looks great.
Alan Gallagher –
Very well made!… went in very easily, Made of metal. Took all but 15, or 20 minutes
tonybaroni7 –
The grill comes with hardware & easy to follow instructions and fills this cavity perfectly. Here’s the challenge: my 2013 F-150 has a factory installed bottom valence as well as a shield on the area where the locking mechanism is, that said, limited working space. If these area’s didn’t have these shields then the installation might have gone quicker/smoother. Being no stranger to attaching aftermarket mods to vehicles, there are always challenges…note the hardware (U-nut and screws) supplied with the grill I found in my situation should be replaced with nuts, bolts & washers. I attached the u-nut to the grill area and test fitted the grill then found tab had to be bent back in place since it would not fit correctly. Next I proceeded to find the correct angle to thread screw into u-nut based on the limited work area. This exercise took well over an hour without any success due to restricted work area and impossible angle required for the screw to be threaded determined by the u-nut. Then, found a video on Youtube that showed the installation but it seems the factory valences I had were not on the truck in the video so the installation seemed to be effortless. What to do? I wasn’t going to disassemble my bumper assembly, So I proceeded to find correct nut, bolt and lock washers in my workshop to attach the grill. Problem solved! I had the grill securely mounted in about 20 minutes using my own hardware so in closing each mounting situation could vary depending what obstructs the grilles mounting points.